12.19.4. Removal, repair and installation of steering transfer
STEERING TRANSFER WITHOUT AMPLIFIER OF STEERING
Centering of steering transfer
Removal
| PERFORMANCE ORDER |
| 1. Remove a weight wire from the accumulator. |
| 2. On models with the carburetor remove the air filter. |
| 3. On models with a washer of headlights release a washer reservoir and move it aside. |
|
4. Using a screw-driver edge as the lever, remove the fixing plate from heads of the bolts fixing steering thirsts for steering transfer, then unscrew bolts and remove washers and a plate. |
| 5. If steering transfer has the shock-absorber, unscrew the bolts fixing a clip of steering transfer and remove the shock-absorber. |
| 6. Establish steering transfer to situation for the movement directly forward. |
| 7. Unscrew two tightening bolts fixing the elastic coupling and move the elastic coupling to a steering shaft. |
| 8. Remove the right forward wheel. |
| 9. In a motor compartment unscrew bolts, the fixing two clips of steering transfer to a partition of a motor compartment, then on the right side take steering transfer. |
| 10. Keep in mind that on some models wires and hoses which before removal of steering transfer need to be disconnected can be attached to steering transfer. |
|
Repair
It is independently possible to replace only protective covers of steering transfer, spherical hinges of cross steering draft and cross steering drafts.
Installation
| PERFORMANCE ORDER |
| 1. Establish steering transfer on a partition of a motor compartment and fix it by new bolts, having tightened them the required moment. |
| 2. Before connection of the elastic coupling check that steering transfer is in situation for the movement directly forward (And = 325 mm) (see rice. Centering of steering transfer). |
| 3. Install into place the elastic coupling and fix it by bolts. |
| 4. Connect steering drafts to a gear lath, at the same time establish under them washers. |
| 5. Establish a plate or an arm of the shock-absorber and tighten bolts the required moment. |
| 6. At installation it is necessary to use the new fixing plate which is established on heads of bolts of fastening of steering drafts. |
| 7. Further installation is made in the sequence, the return to removal. |
|
STEERING TRANSFER WITH THE AMPLIFIER OF STEERING
Removal
| PERFORMANCE ORDER |
| 1. Remove a weight wire from the accumulator. |
| 2. On models with the carburetor remove the air filter. |
| 3. On models with a washer of headlights release a washer reservoir and move it aside. |
| 4. Disconnect hoses on the left side of steering transfer and close a hose and an opening for a hose suitable traffic jams. |
| 5. Using a screw-driver edge as the lever, remove the fixing plate from heads of the bolts fixing steering thirsts for steering transfer, then unscrew bolts and remove washers and a plate. |
| 6. If steering transfer has the shock-absorber, unscrew the bolts fixing a clip of steering transfer and remove the shock-absorber. |
| 7. Establish steering transfer to situation for the movement directly forward. |
| 8. Unscrew two tightening bolts fixing the elastic coupling and move the elastic coupling to a steering shaft. |
| 9. Remove the right forward wheel. |
| 10. In a motor compartment unscrew bolts, the fixing two clips of steering transfer to a partition of a motor compartment, then on the right side take steering transfer. |
| 11. Keep in mind that on some models wires and hoses which before removal of steering transfer need to be disconnected can be attached to steering transfer. |
|
Installation
| PERFORMANCE ORDER |
| 1. Establish steering transfer on a partition of a motor compartment and fix it by new bolts, having tightened them the required moment. |
| 2. Before connection of the elastic coupling check that steering transfer is in situation for the movement directly forward. |
| 3. Install into place the elastic coupling and fix it by bolts. |
| 4. Connect steering drafts to a gear lath, at the same time establish under them washers. |
| 5. Establish a plate or an arm of the shock-absorber and tighten bolts the required moment. At installation it is necessary to use the new fixing plate which is established on heads of bolts of fastening of steering drafts. |
| 6. Further installation is made in the sequence, the return to removal. |
| 7. Fill in fresh liquid in hydraulic system of the amplifier of steering and remove air from system. |
|
